Cta 7 Series Bedienungsanleitung

REHABILITATION PRODUCTS SERIES 6 & 7 OWNER/USER MANUAL For your safety and comfort read carefully and understand all of the features pri

1. Clamp Type – to adjust height simply loosen clamp bolt, move to desired position, retighten clamp bolt. 2. Incremental Hole Type – to adjust heig

SECTION 5. TRANSPORTING YOUR POWER CHAIR Transporting your Power Chair in motor vehicles can be easily achieved by the following methods. STATION WA

FIGURE 2. FOLD DOWN BACKREST

SECTION 6. BATTERY CHARGING AND MAINTENANCE Keeping the Power Chair working to its maximum potential it is recommended the batteries be charged every

SECTION 7. ROUTINE MAINTENANCE DAILY Charge your batteries every night so your Power Chair is ready to go when you are. WEEKLY 1. Check tyre pressu

SECTION 8. TROUBLE SHOOTING If your Power Chair will not go, follow this checklist 1. Check that the lights on control box are illuminated. 2. If t

SECTION 9. PENNY & GILES PILOT + SERIES CONTROLLER Figure 3. Penny & Giles Controller

CONTROLS On/Off Push button This is a green pushbutton switch fitted in front of the joystick, which turns the controller On and Off. Do not use this

1. To adjust speed when in this mode – The maximum speed can be adjusted by left or right movements of the joystick. Left will decrease the speed, ri

SECTION 10. DYNAMIC CONTROLS CONTROLLER Figure 5. Dynamic Controller

TABLE OF CONTENTS SECTION 1. INTRODUCTION SECTION 2. STANDARD FEATURES SECTION 3. WARNINGS SECTION 4. TRANSPORTING THE POWER CHAIR SECTION 4.

CONTROLS DX – G90A REMOTES On/Off Button – This is a white pad located in front of joystick control knob. It is also identified by having 1/0 prin

Figure 6. Dynamic Control Panel

Dynamic Shark Controller Models DK – REMA - No Seat Functions DK – REMB – Two Seat Functions Controls All user controls can be accessed from the s

The Shark Information Gauge The Shark information gauge is the primary source of user feedback. It displays every possible status that SHARK may have

Turning the SHARK On and OFF Turning the Power ON • Press the Power Button • All indicators will light briefly • Either the current battery cha

Sleep Mode Some Sharks may be supplied factory programmed with a Sleep feature that will automatically turn SHARK off if the joystick has not been mov

Note: User should ensure proper mode is selected before attempting to drive or operate actuator. Locking the SHARK Some SHARKS may be supplied facto

Note: If the user does not press the horn button twice before the countdown is complete, the HORN will sound a short BEEP and Shark will turn itself o

SECTION 11. PRECAUTIONS FOR CONTROLLER USE The Dynamic and Penny & Giles controller has been designed with the user safety as the prime considera

SECTION 12. TRANSFERRING TO AND FROM YOUR POWER CHAIR. The Glide Rehabilitation Products Power Chair is designed in such a way that transferring in a

SECTION 1. INTRODUCTON Thank you for choosing the Glide Power Wheelchair. An Australian designed and manufactured product, which complies with AS 3

SECTION 13. BATTERY WIRING DIAGRAM 2 x 36Amp Hour Sealed Deep Cycle Batteries Consult your Glide Products agent when replacement is required.

SECTION 14. SPARE PARTS User Serviceable Parts TYRES 8” Pneumatic Front (200 x 50) Part Number – 202602 9” Pneumatic Front (2.80/2.50)

SECTION 15. WARRANTY Lendal Pty Ltd (trading as Glide Rehabilitation Products) warrants the following as listed: Controllers 12-months warranty Con

IMPORTANT 1. Lendal Pty Ltd (trading as Glide Rehabilitation Products) does not warrant either expressly or impliedly the suitability of the Glide

SECTION 2. STANDARD FEATURES The illustration (Fig 1. below) is a list of the Series 6 & Series 7 standard features 1. Drop Down Arms 2. Batt

SECTION 3. WARNINGS Read and understand the warnings stated in this section. To the Occupant WARNING! 1. Before using this chair, obtain advice a

Even though the “CTA System” improves manoeuvrability and stability, this does not negate the effect or take into account, circumstances, which put th

• Drive chair at a slow steady speed .Do not allow chair to accelerate over normal speed. Centre the joystick to allow it to slow down or stop. • Ne

MODIFICATIONS WARNING! Never make any modifications or use non-approved Glide Rehabilitation Products parts on your power chair. Doing so may cause a

SECTION 4. OPERATING YOUR POWER CHAIR CONTROLLER Your new Power Chair has the option of two types of control systems, Dynamic Controls or Penny &